You are using an old version of this browser, for best results please update.
In order to provide you with the best online experience this website uses cookies. By using our website, you agree to our use of cookies. More Info.
LokPilot 61600 Mfx v3.0 M4 8 pin DCC Decoder

LokPilot 61600 Mfx v3.0 M4 8 pin DCC Decoder

Product Code: 101353
There are currently no reviews listed for this item. If you you would like to submit a review for this item please click 'Write A Review' below and complete the online form.
Out Of Stock
Awaiting
delivery date
£40.88
(£34.07 excl. VAT)
The LokPilot V3.0 M4 was developed from scratch especially for Märklin® systems.
(Not for NMRA DCC use.)


Operational modes
The LokPilot V3.0 M4 is a genuine multi-protocol decoder: Besides its main field of application in combination with mfx® stations, it handles Motorola® command stations (e.g. Märklin® 6021) as well as conventional AC driven layouts. The LokPilot V3.0 M4 recognizes the operational mode fully automatically and converts on the fly.Motor management

The LokPilot V3.0 M4 runs DC – and coreless motors directly, while all-current motors need a Hamo-magnet retrofit. The motor is driven by 40 kHz Pulse width frequency (PWM) for a super silent, safe run. Together with the 128 mfx® speed steps and fourth generation back EMF, unprecedented performance is realized.

Analog operation
The LokPilot V3.0 M4 also operates on analog AC layouts, on which even starter – and top speed can be limited individually. At last you can slow down your old high-speed runners.

Functions
The LokPilot V3.0 M4 sports four function outputs, which can be dimmed, and allocated individually to a function. Besides beacon, strobe and alternate flashing, there is a Mars light as well as a Gyra light.

Programming
The LokPilot V3.0 M4 can be adapted to any loco or operational mode. For this, you can comfortably change parameters with the systems-stations – during operation and without having to open the loco or put it on a programming track. That’s made possible through the built-in, genuine Duplex communication between systems-center station and decoder. For owners of 6020®, 6021® – or delta® stations the LokPilot V3.0 M4 decoder utilises the time-proven, simple programming procedure.

Safeguard
All function outputs and the motor connection are overload – and short circuit protected.

Built-in future
The internal decoder software can be replaced by a new firmware update, if desired.

Operational modes: M4 with 128 speed steps
Digital Motorola® (old and new) with 14 or 28 speed steps, up to 255 addresses in Motorola® use
Analog AC (de-selectable)
Automatic recognition of operational mode
Supports Märklin® braking section. Wrong-direction bit.
Intelligent programming mode with Märklin® 6021®
Switching speed and acceleration as well as deceleration key selectable

Throttle: 1.1 A continuous load
Runs DC, coreless and AC motors (with permanent magnet)
Silent, safe 16 / 32 kHz pulse width frequency motor regulation
Motor output overload protected. Fourth generation back EMF (de-selectable)

Function output: 4 outputs, 2 of which for lighting
250mA load per output
500mA total load of all function outputs. Overload protected.
Outputs short circuit protected (function mapping)

Dimensions: 23.5mm x 15.5mm x 5.5mm (0.94 x 0.62 X 0.22 inch)
There are currently no reviews listed for this item. If you you would like to submit a review for this item please click 'Write A Review' below and complete the online form. Write A Review
LokPilot 61600 Mfx v3.0 M4 8 pin DCC Decoder
Product Code:101353
LokPilot 61600 Mfx v3.0 M4 8 pin DCC Decoder
The LokPilot V3.0 M4 was developed from scratch especially for Märklin® systems.
(Not for NMRA DCC use.)


Operational modes
The LokPilot V3.0 M4 is a genuine multi-protocol decoder: Besides its main field of application in combination with mfx® stations, it handles Motorola® command stations (e.g. Märklin® 6021) as well as conventional AC driven layouts. The LokPilot V3.0 M4 recognizes the operational mode fully automatically and converts on the fly.Motor management

The LokPilot V3.0 M4 runs DC – and coreless motors directly, while all-current motors need a Hamo-magnet retrofit. The motor is driven by 40 kHz Pulse width frequency (PWM) for a super silent, safe run. Together with the 128 mfx® speed steps and fourth generation back EMF, unprecedented performance is realized.

Analog operation
The LokPilot V3.0 M4 also operates on analog AC layouts, on which even starter – and top speed can be limited individually. At last you can slow down your old high-speed runners.

Functions
The LokPilot V3.0 M4 sports four function outputs, which can be dimmed, and allocated individually to a function. Besides beacon, strobe and alternate flashing, there is a Mars light as well as a Gyra light.

Programming
The LokPilot V3.0 M4 can be adapted to any loco or operational mode. For this, you can comfortably change parameters with the systems-stations – during operation and without having to open the loco or put it on a programming track. That’s made possible through the built-in, genuine Duplex communication between systems-center station and decoder. For owners of 6020®, 6021® – or delta® stations the LokPilot V3.0 M4 decoder utilises the time-proven, simple programming procedure.

Safeguard
All function outputs and the motor connection are overload – and short circuit protected.

Built-in future
The internal decoder software can be replaced by a new firmware update, if desired.

Operational modes: M4 with 128 speed steps
Digital Motorola® (old and new) with 14 or 28 speed steps, up to 255 addresses in Motorola® use
Analog AC (de-selectable)
Automatic recognition of operational mode
Supports Märklin® braking section. Wrong-direction bit.
Intelligent programming mode with Märklin® 6021®
Switching speed and acceleration as well as deceleration key selectable

Throttle: 1.1 A continuous load
Runs DC, coreless and AC motors (with permanent magnet)
Silent, safe 16 / 32 kHz pulse width frequency motor regulation
Motor output overload protected. Fourth generation back EMF (de-selectable)

Function output: 4 outputs, 2 of which for lighting
250mA load per output
500mA total load of all function outputs. Overload protected.
Outputs short circuit protected (function mapping)

Dimensions: 23.5mm x 15.5mm x 5.5mm (0.94 x 0.62 X 0.22 inch)
£
(£ excluding VAT)